Untethered Jailbreak iOS 4.3.2 on iPhone 4, 3GS, iPod Touch 3G/4G and iPad Using Redsn0w 0.96 RC13 on Windows & Mac! [Guide]

by Jawwad in Guides, iPad, iPhone, Mobile | 1 comment


Finally the wait is over folks! iOS 4.3.2 is available for quite some time now. Earlier we had Redsn0w 0.9.6RC9 available that can jailbreak iOS 4.3.1 untethered on all iDevices except iPad 2. Untethered jailbreaking is achieved by using the exploit provided by the Stefan Esser that we reported some time ago. Good news as we reported before is that surprisingly Apple has NOT patched the untethered exploit in the latest iOS 4.3.2! All of us were waiting for a an official release from iPhone Dev Team for the untethered JB tool such as RedSn0w. So, they didn’t disappoint as moments ago iPhone Dev team has released the RedSn0w 0.96 RC13 that allows to do the untethered jailbreak on iOS 4.3.2 for the all the supported devices!!

Earlier before this we have posted the instructions for the tethered jailbreak of iPhone 4, iPad, iPod touch 4G.

Update: Redsn0w 0.96 RC14 is now available that includes better support for iPhone 4. So the download links are updated for RC14 release. Jailbreaking procedure is exactly same as posted here.

Note: Please stay away from this method if your phone is dependent on a carrier unlock! Instead wait for the new official  PwnageTool / Sn0wbreeze tool release that will allow to do do untethered jailbreak for the iOS 4.3.2 iDevices while preserving your baseband. Actually, this is method is useful only if you are NOT dependent on a carrier unlock for both Mac and Windows users.

Now follow these instructions:

Programs required:

Step 1: Download the Redsn0w 0.9.6 RC13 and iOS 4.3.2 stock FW and save both of them to the desktop. Extract the Redsn0w application in a folder on the desktop.

Step 2: Execute RedSn0w application from there that was extracted earlier.
Step 3: Once RedSn0w appears click the Browse button. Then browse the iOS 4.3.2 stock FW that downloaded in Step 1 and open it (as shown in the illustration below).

image17 | Untethered Jailbreak iOS 4.3.2 on iPhone 4, 3GS, iPod Touch 3G/4G and iPad Using Redsn0w 0.96 RC13 on Windows & Mac! [Guide]

image18 | Untethered Jailbreak iOS 4.3.2 on iPhone 4, 3GS, iPod Touch 3G/4G and iPad Using Redsn0w 0.96 RC13 on Windows & Mac! [Guide]

Notice this popup that appears for the users that are using the iPhone 3GS. As instructed in the picture below you can find out the model of the iPhone 3GS easily.

image19 | Untethered Jailbreak iOS 4.3.2 on iPhone 4, 3GS, iPod Touch 3G/4G and iPad Using Redsn0w 0.96 RC13 on Windows & Mac! [Guide]

Step 4: Once the firmware has been verified click the Next button to continue.

image20 | Untethered Jailbreak iOS 4.3.2 on iPhone 4, 3GS, iPod Touch 3G/4G and iPad Using Redsn0w 0.96 RC13 on Windows & Mac! [Guide]

Step 5: RedSn0w will now prepare the jailbreak data.
Step 6: From this window you can select the jailbreak options you would like.
- Make sure Cydia is selected.
- Notice that RedSn0w can Enable multitasking (iPhone 3G only, no display of this option on 3GS needed!). If you do not need multitasking we would recommend deselecting it as it makes your iPhone 3G run very slow.

image22 | Untethered Jailbreak iOS 4.3.2 on iPhone 4, 3GS, iPod Touch 3G/4G and iPad Using Redsn0w 0.96 RC13 on Windows & Mac! [Guide]
Don’t forget to check Install iPad Baseband to update your baseband to the 06.15 iPad version for unlock (in case you want to unlock your iPhone 3GS later on). Click Yes when prompted to confirm. Now click the Next button to continue
Step 7: Now plug your iPhone into the computer and make sure its OFF then click the Next button.

image thumb3 | Untethered Jailbreak iOS 4.3.2 on iPhone 4, 3GS, iPod Touch 3G/4G and iPad Using Redsn0w 0.96 RC13 on Windows & Mac! [Guide]
Step 8: RedSn0w will now guide you through the steps to get into DFU mode. Hold down both the Home button and the Power button for 10 seconds. Release the Power button and continue holding the Home button until RedSn0w detects the device.

image24 | Untethered Jailbreak iOS 4.3.2 on iPhone 4, 3GS, iPod Touch 3G/4G and iPad Using Redsn0w 0.96 RC13 on Windows & Mac! [Guide]
Step 9: RedSn0w will then do it’s processing and you will be notified when RedSn0w it is done. Click the Finish button. When your iPhone finishes rebooting it will be jailbroken with Cydia on the SpringBoard!

Enjoy! now you have a fully untethered jailbroken iDevice on iOS 4.3.2 (optionally) with the baseband upgraded to 16.5.00!,

Now you can continue this step-by-step guide on how to unlock your iPhone 3GS, iPhone 4 using Ultrasn0w Fixer For 4.3.2  that we published earlier today.

NOTE:
If you have problems with RedSn0w on Windows Vista or Windows 7. Right click the executable and set it to run as administrator in Windows XP compatibility mode.

You Might Like:




Get Free Email Updates


Inspired Geek is your primary source for latest tech news, guides and articles on Windows software, games, Apple and Android devices.


  • Get extensive coverage on latest tech news.
  • Exclusive guides on rooting, jailbreaking and unlocking mobile devices.
  • Useful apps and tips&tricks for your iOS and Android devices.
  • Exlclusive Top Countdowns for the best software.

This post was written by...

for Inspired Geek.

Hi! We are trying our best to make this spot most interesting and useful for discovering news, articles, tips & tricks and bringing you the latest in Computer, Mobile and Internet technology areas. Please support our efforts by giving your feedback, subscribing to Inspired Geek RSS (Link on top & bottom of the page), by promoting us on social websites (Facebook, Digg, Twitter, StumbleUpon etc.) or any other way you might feel convenient. Thanks for your support!

Previous post:

Next post:

wordpress counter